Aluminum fueled Hydrogen Generator kit

This is the assembled and pre-wired version of the Aluminum fueled Hydrogen Generator

Pure Hydrogen can be made from Aluminum and Lye by the following equation

Sodium aluminate is produced and pure Hydrogen Gas

[ You can opt out of Google Ads if you are a registered user at /ad-options ]

2 Al + 2 NaOH + 2 H2O → 2 NaAlO2 + 3 H2

See https://en.wikipedia.org/wiki/Sodium_aluminate

The reaction has two issues, it is highly exothermic, meaning due the reaction itself it can get hot enough to boil the water of the equation and produce both steam in conjunction with the hydrogen meaning to separate the steam one has to bubble the product though cool water to re-condense the steam in the Hydrogen gas back into aqueous form, and the other issue is fresh feed stock of water must be added to keep producing Hydrogen.   

This product is designed to produce enough gas for powering a small engine  of six to eighteen horsepower .  Ideally it is setup to automatically feed itself liquid feedstock and has a port to manually add aluminum and lye crystals once the pressure is released or the reaction chamber can be unscrewed to do so.

 A best feedstock is urine due to the salt content which assists in keeping oxidation low.

This is a "nasty" way to make hydrogen because  you will be dealing with a caustic solution all the time that can burn the skin and corrode most painted surfaces 

You will also need at least a three to five gallon buffer storage tank.  It can  be an air or air compressor tank, but if so must be  evacuated by vacuum pump first.  If a Propane tank  not required so long as it has not been opened to atmospheric air.

If you choose this route to produce Hydrogen, you need a source of cheap easy to get aluminum and a place to buy true BULK Sodium Hydroxide, because it can be very expensive purchased in small qualities - a.k.a. like single cans of Crystal Drano - which is Sodium Hydroxide.  The up side - is there is no need to build a beefed up alternator system that can produce the amperage needed for electrolysis.

The serious and dangerous  down side is Sodium Hydroxide eats and dissolves flesh. It is what people call a chemical "burn", but the reality is the only way to stop the reaction is to flood the area immediate ly with water - but that is really too late as people are made of flesh. Thus for instance one drop in an eye will instantly and permanently blind that eye. There is no washing it out - you will loose sight - period. Take proper precautions when dealing with Sodium Hydroxide, to include proper protective gear at all times especially eye protection

Another down side is if Sodium Hydroxide is left exposed to the air, sodium hydroxide will absorb carbon dioxide, and gradually become sodium carbonate (washing soda / soda ash).which is then useless to produce Hydrogen.

You must depressurize - as in allow the reaction to naturally subside - and then open it to feed more aluminum to the generator periodically and clean out then the precipitate Sodium_aluminate periodically and unless the reaction is 100 balanced, the precipitate will be caustic - that is it will chemically burn bare skin and damage painted surfaces etc.

To stop or slow the reaction one must let the water deplete if it gets too hot, and that means something must monitor the heat.  Purity of the Hydrogen gas is measured by a digital gauge and allowed to fill a tank up to 100 psi.

This product will cut off feeding more liquid feedstock if the pressure rises above a certain level and does not drop.  Eventually the reaction will subside and pressure usually will not rise above the capacity of the housing.

This is not a hydrogen making process for the poor attention to detail type person.

This will make a 8 inch round by 1 foot tall enclosure Rated with a maximum burst pressure of 160 PSI and an operating pressure of 20 psi. 

You will need to drill and cut as required for your design or tap and/or glue fittings in for your lines as you desire.

This is a custom part upon ordering is not refundable nor will be returnable.

Has a suggested design diagram on how to build a good pressure gas housing and why along with a list of materials.

  Four  hours of consulting is available included via email in the purchase price via our message system through this site only.  This item is sold outright and may be used as you see fit. We will not however, assist with unlawful or dangerous implementations of this product.

This is a custom part upon ordering is not refundable nor will be returnable.

This a la carte option does not include, tank, plumbing, gas generator design instructions, pump, hoses, or sensors - housing materials only - you need to have us design a full system for that above to be included.

Stainless Steel pressure Dome kit - Housing parts only 300 PSIG  200 DEGREES F

Stainless temperature probe => see https://bigbay4bestbuys.com/thermocouple

Selectable pressure  and purity gauge - dual digital gauge => see https://bigbay4bestbuys.com/content/hydrogen-purity-gauge-and-controller

Float switch => see https://bigbay4bestbuys.com/stainless_vertical_switch

WHILE THE WEBSTORE WILL ACCEPT A BANKCARD PAYMENT WE RESERVE THE RIGHT, AND USUALLY WILL, REFUND THAT PAYMENT METHOD AS THIS ITEM IS GENERALLY VENDED BY BITCOIN PAYMENT ONLY

If you need info on how to buy with Bitcoin see => https://bigbay4bestbuys.com/bitcoin_climb

Weight: 4 lb
List price: $499.00
Price: $811.00
$811.00
Hydrogen purity gauge and controller
Sensor for purity gauge and controller (0-60 PSI)
Adjustable diaphragm pressure controller switch insulation and sleeve
Stainless Steel Vertical switch
Stainless Housing for Aluminum fueled Hydrogen Generator
[ You can opt out of Google Ads if you are a registered user at /ad-options ]
English
SKU: 300 psi sensor / multi_gauge / sensor_60 / Stainless_dome / ss_switch_vert
[ You can opt out of Google Ads if you are a registered user at /ad-options ]