Custom made electrical item NOT Returnable or Refundable
The FreeFuelSystem is a Pure Gas Generator system that makes lawful Hydrogen Motor fuel in accord CA CCR 2292.7 with an orderant. It requires dual alternators (not included) if powering and engine and it is set up for each application specifically. This item is licensed and not sold so there is a monthly fee and it has a warranty for life as long as the terms are complied with a and the license fees remain paid. The customer is NOT allowed to design their own application without approval. There is a stationary version available/ If you have questions or want a specific design then purchase this FIRST => https://bigbay4bestbuys.com/gashole_video and ask your question in the notes section, as in that way we get a full indication of who you are as a real person and the TOS then becomes effective and your specific system can be spec'ed out for you. See https://bigbay4bestbuys.com/content/terms-service-andor-use
This item makes 99.99 percent PURE Hydrogen and can be configured for fuelling almost any device that currently use Natural Gas, Propane or Gasoline, and can be used to bi-fuel Diesel applications
There are two types of Hydrogen Generators - the PEM design and the Hoffman design. For more info, see - which Hydrogen Generator is best for the job ?? The PEM design uses a membrane and electronic controller - and the Hoffman design is a mechanically separated gas design. This is the PEM type design.
This product is eligible for a lifetime warranty ONLY when purchased as part of a complete freefuelsystem generator and timely fees remain paid. It requires support sensors and electronics and this is ONLY the PEM stack itself. Without the proper power regulation and sensors you will likely immediately destroy this item.
PEM Electrolyzer Stacks are an advanced patented product, which is lower voltage and higher efficiency, energy-saving and of environmental protection, producing hydrogen and oxygen through the electrolysis of pure water without adding alkali
The proton exchange membrane (PEM), which only allows water and positive ions to cross between compartments. A PEM electrolyzer utilises a solid polymer electrolyte (SPE) to conduct protons from the anode to the cathode while insulating the electrodes electrically. Thus the PEM and SPE technology are eh same thing. The membrane also serves as the electrolyte in the cell, eliminating the need for hazardous liquid electrolytes such as concentrated potassium hydroxide. PEM water electrolysis simply splits pure deionized water (H2O) into its constituent parts, hydrogen (H2) and oxygen (O2), on either side of this membrane. When a DC voltage is applied to the electrolyzer, water fed to the anode, or oxygen electrode, are oxidized to oxygen and protons, while electrons are released. The protons (H+ ions) pass through the PEM to the cathode, or hydrogen electrode, where they meet electrons from the other side of the circuit, and are reduced to hydrogen gas. The two reactions that occur in the cell are as follows:
1. 2H2O -> 4H+ + 4e- +O2
2. 4H+ + 4e- -> 2H2
Thus, the only possible components of the streams are hydrogen, oxygen and water moisture, as shown below.
• Redundant renewable energy transformation and storage
• Lab experiment and teaching
• Laboratory analytic instrument
• Hydrogen healthy care industrial
• Hydrogen beauty industrial
• Fuel for special field
• Hydrogen supply for fuel cell
• Other pure H2 application field
• Produce hydrogen by electrolysis pure water without adding alkaline
• No corrosion or pollution
• High hydrogen purity
• Low electrolyzer cell resistance
• No heat and long desiccant replacement cycle
• Lower power consumption and high electrolysis efficiency
• Cannot be used in freezing climates or allowed to overheat
• MUST use de-ionized or pure distilled water or the PEM stack will clog with precipitates of the minerals of the hard water. (water de-ionization system and tank not included)
|H2 Flow Rate||mL / min||0 - 60||0 - 120||0 - 180||0 - 240||0 - 300||0 - 500||0 - 1000|
|O2 Flow Rate||mL /min||0 - 30||0 - 60||0 - 90||0 - 120||0 - 150||0 - 250||0 - 500|
|Voltage||V (DC)||2 (9A)||4 (9A)||6 (9A)||8 (9A)||2 (45A)||4 (36A)||8 (36A)|
|Membrane Type||-||Nafion PFSA|
|Titanium sintering carpet|
|Precious metal electrode|
|Needs deionized or re-distilled water|
|Water Resistivity: >1 MΩ*cm|
|Water Conductivity: <1 us/cm|
General lead time of two weeks to be expected.
Freefuelsystem with controls and 2 gal storage tank which will pressurize to 60 psi - size approx 18 x 18 x 12 inches.
NOT Included but may be required
Appropriate power supply source - Alternator or Transformer, Water purification with deionization system, tank if to be mobile, pump if to be mobile , pressure regulator for system it is hooked up to - i.e. fuel injection or household gas line system
OBVIOUSLY THIS PRODUCT CAN BE DANGEROUS IF YOU DO NOT EXERCISE PROPER PRECAUTIONS AND FOLLOW INSTALLATION AND APPLICATION DESIGN PARAMETERS AND INSTRUCTIONS - IT MAKES THE EQUIVALENT OF NATURAL GAS OR PROPANE AND MUST BE TREATED WITH GREATER RESPECT DUE TO THE SPEED OF WHICH A HYDROGEN FLAME SPREADS AND IS INVISIBLE IN ORDINARY DAYLIGHT.
WHILE THE WEBSTORE WILL ACCEPT A BANKCARD PAYMENT WE RESERVE THE RIGHT, AND USUALLY WILL, REFUND THAT PAYMENT METHOD AS THIS ITEM IS GENERALLY VENDED BY BITCOIN PAYMENT ONLY
If you need info on how to buy with Bitcoin see => https://bigbay4bestbuys.com/bitcoin_climb