250 amp GM CS-144 family Alternator Kit

$799.00
SKU: hpc_144_alternator_kit
UC_Image: 
English

 

 

 

 

 

 

This is a 250 amp kit for GM 17SI, 21SI, 22SI, 23SI, 27SI, 33SI, 34SI, or CS144 

This will push up to 500 amp in bursts the CS-144 is the one on the right

This is a custom part upon ordering is not refundable nor will be returnable.

You need this to power a decent size Gas Generator.

The CS-144 family alternator can be any mounting style

Includes NEW:

** Stator

** 70 amp Non-Avalanche Rectifier set

** Brush set

** Voltage regulator

 

***** You could also run a welder with this alternator and the right supplemental circuitry *****

 

Does NOT include the case or rotor - you need to have an alternator type like this. Add $200 for full alternator, exchange core is $100. 

 

We use these on all GM vehicles depending on the vehicle or engine application. Depending on how set up it could reduce cost per mile fuel use to 10% of the total you pay now.  ($4,000 per year down to $400 per year)

 

You can mount dual units.  We can provide GM's wiring.

 

4 hours consulting included.  If you want us to ship this item without setup, it is then no longer eligible for EPA and CARB EO or waiver.   See 40 CFR Part 85, Subpart F

 

40 CFR Part 85, Subpart F is . . .

 Subpart F--Exemption of Aftermarket Conversions From Tampering 
 Prohibition
 
Sec. 85.503 Conditions of exemption.

 (a) As a condition of receiving an enforcement exemption from the 
tampering prohibitions contained in section 203 of the Act, an 
aftermarket conversion certifier must certify the aftermarket conversion 
system, using the applicable procedures in part 86 of this chapter, and 
meeting the applicable standards and requirements in Secs. 85.504 and 
85.505, and accept liability for in-use performance of the aftermarket 
conversion system as outlined in this part.
 (b) As a condition of receiving an enforcement exemption from the 
tampering prohibitions contained in section 203 of the Act, an 
aftermarket conversion installer must:
 (1) Install a conversion which has been certified as a new vehicle 
or engine, using the applicable procedures in part 86 of this chapter, 
and meeting the applicable standards and requirements in Secs. 85.504 
and 85.505; and
 (2) Accept liability for in-use performance of the aftermarket 
conversion system as outlined in this part.


Now here the relevant language above is (b)(2) which requires the manufacturer to "accept liability for in-use performance of the aftermarket conversion system outlined in this part"

That means if we design and build it, we must make sure you use it according to the law and that we can have the power to do so.  The only legal way to do this is to license it, even IF it is CARB exempted by order, and the only way we can be assured our product will not be tampered with after design is to license it only and/or lease it out.

The EPA memo makes clear that only closed loop systems can be now used, and this in conjunction with the manufacturer maintenance provision means we must maintain control over being able to  - and being the only party who can - adjust the ECM which is an after market part and uses our after market part system.  Thus we can only license our systems and lease the items out - not sell them outright.

 

Vended under the site license terms. 

 

Please review carefully the Terms of Service you agreed to when creating your account

 

This is a custom part upon ordering is not refundable nor will be returnable.

 

EPA and CARB Exemptable for your application

Price: $799.00
Weight: 10 lb
Dimensions: 10 in × 8 in × 4 in