Hydrogen Metal Hydride tank

UC_Image: 

This can be used to store hydrogen for a dedicated on the fly system for quick start so as to not wait for pressure to build for our separated gas Hydrogen systems.

 

Actual item NOT pictured.

 

This is a custom part upon ordering is not refundable nor will be returnable.

 

Will partly recharge with a lengthy drive depending on pressure

 

The Gas Generator is not included in this price.  You will need a separated gas generator or source that can maintain approximately 30 to 45 psi

 

This tank cannot be used to propel a vehicle any appreciable distance

 

900 Liters:
Diameter:3.5in.
Length:15.1in.
Weight:14lbs.
Nominal Capacity:762 liters (68 grams)
Nominal Discharge Rate:600W
Standard Fitting: Female 1/8 NPT interface
Optional Quick Connect Couplings available

 

Requires site license purchase for engineering setup.

 

We set this system up with our software for your vehicle depending on the vehicle or engine application. Depending on how set up it could reduce cost per mile fuel use to 10% of the total you pay now.  ($4,000 per year down to $400 per year)

 

This article is intended for our fuel injection with the OEM or with our piggy-back system which can then automatically switch back to the OEM system in full and cut-off and lock of the gas source if the Gaseous Gas system fails.  Set up to be; and, is shipped EPA and CARB compliant.

 

4 hours consulting included.  If you want us to ship this item without setup, it is then no longer eligible for EPA and CARB EO or waiver.   See 40 CFR Part 85, Subpart F

 

40 CFR Part 85, Subpart F is . . .

 Subpart F--Exemption of Aftermarket Conversions From Tampering 
 Prohibition
 
Sec. 85.503 Conditions of exemption.

 (a) As a condition of receiving an enforcement exemption from the 
tampering prohibitions contained in section 203 of the Act, an 
aftermarket conversion certifier must certify the aftermarket conversion 
system, using the applicable procedures in part 86 of this chapter, and 
meeting the applicable standards and requirements in Secs. 85.504 and 
85.505, and accept liability for in-use performance of the aftermarket 
conversion system as outlined in this part.
 (b) As a condition of receiving an enforcement exemption from the 
tampering prohibitions contained in section 203 of the Act, an 
aftermarket conversion installer must:
 (1) Install a conversion which has been certified as a new vehicle 
or engine, using the applicable procedures in part 86 of this chapter, 
and meeting the applicable standards and requirements in Secs. 85.504 
and 85.505; and
 (2) Accept liability for in-use performance of the aftermarket 
conversion system as outlined in this part.


Now here the relevant language above is (b)(2) which requires the manufacturer to "accept liability for in-use performance of the aftermarket conversion system outlined in this part"

That means if we design and build it, we must make sure you use it according to the law and that we can have the power to do so.  The only legal way to do this is to license it, even IF it is CARB exempted by order, and the only way we can be assured our product will not be tampered with after design is to license it only and/or lease it out.

The EPA memo makes clear that only closed loop systems can be now used, and this in conjunction with the manufacturer maintenance provision means we must maintain control over being able to  - and being the only party who can - adjust the ECM which is an after market part and uses our after market part system.  Thus we can only license our systems and lease the items out - not sell them outright.

 

Vended under the site license terms.   Any required additional EPA or CARB certification costs for your application are born by the client.  Discounts available for fleet order setups.

 

Please review carefully the Terms of Service you agreed to when creating your account

 

Please understand, a large number of people normally want to contact  us with pre-sales questions of a detailed nature, and in that case normally they are ignored unless they have made at least the most basic purchase of the license.
 

This is a custom part upon ordering is not refundable nor will be returnable.

 

EPA and CARB Exemptable for your application

Weight: 35 lb
Price: $2,399.00
$2,399.00
SKU: hpc_H2_900_hydride
English